How To Use

Surface Preparation 1

For pitted surfaces, carefully sand and level using medium/course grit paper (400-600) to maximize smoothness and flatness.
Remove any contamination with SCUDOPICKLING 100AB solvent cleaner, especially for metal surfaces.

Primer Application 2

Apply TUTTOPRIMER IC100B (100%) + TUTTOCATALYST IC80 (80%) mix ratio 5:4 using an HLVP spray gun (or normal spray gun) with nozzles 1.2-1.3 mm at a nozzle pressure of 1.50 bar (217.5 psi).
Shake well before use. Let it dry at 60°-70°C for 70 minutes, then allow it to rest for 30 minutes at ambient temperature (20-25°C) for 12-24 hours. Ensure drying in a clean, dust-free environment and avoid touching coated surfaces.

Chrome Application 3

Shake well the 1K TUTTOCHROMAME STD TC20 before pouring it into the HLVP spray gun.
Use nozzles sized 1-1.2/1.3 mm at a nozzle pressure of 1.50 bar.
Apply three layers of TUTTOCHROME with crossed strokes until the surface is completely covered. Recommended spraying from bottom to top and then cross left to right.
Let it dry at 60°-70°C for 70 minutes. For optimal results, attend at ambient temperature for 24 hours. The longer the solvents evaporate, the higher the reflectivity (up to 90%-95% spherical reflectivity).

Top Coat Step 4

Apply CLEARTOP MT300 (100%) + CLEARCATALYST MT936 (40%) mix ratio 5:2 with an HLVP spray gun (or normal spray gun) with nozzles 1.2-1.3 mm at a nozzle pressure of 150 bar (2175 psi).
If special coloring is required, add CME Pigments to CLEARTOP MT300 (100%) + CLEARCATALYST MT936 (40%) according to the specified mix ratio % for each CME Pigment on the bottle label.
Let it dry at 60°-70°C for 1 hour or at room temperature for 12-24 hours. The product can be handled and packaged after 3 hours. Always apply a second layer of CLEARTOP MT300 (100%) + CLEARCATALYST MT936 (40%) after color coating for a high-quality, glossy, and durable finish.

SURFACE PREPARATION 1

Remove any contamination that could interfere with the top coating adhesion.
Prior to applying ScudoChromame 602FX Flextop it is advisable to thoroughly clean the plastic surface with the special solvent SCUDOPICKLING 52MT.
It can be applied directly to a well prepared surface that has been sanded to a perfectly flat, fine uniform finish and perfectly clean and dry.

CATALYSER (Hardner) 2

SCUDOCHROMAME 5Q2MT IS A 2K PRODUCT
Mix Cathalysed ratio 5:2 SCUDOCHROMAME 602FX (100%)+ SCUDOCATALYST 52MT (40%) Shake well before use.

APPLICATION METHODS 3

Brush; Roller HVLP Airless spray gun - only PROFESSIONAL USE
Respect a 5- 10 minutes interval between each coat.
Nozzle tip 1,3-1,5 mm Pressure at nozzle (minimum) 300 bar/4351 psi

OPERATING ENVIRONMENT 4

6D2MT should be applied in a clean temperature and humidity controlled environment.
Recommended conditions for application are 20 - 25°C (68 - 77°F) and 30 - 60% relative humidity.

Coverage 5

5 to 6 sqm per 1 [ tin of SCUDOCHROP4AP4E 602FX One Tin will cover up to 5 sqm in one coat.
For best results apply two coats which gives an average coverage of 2 to 3 sgm depending on surface condition and application.

DRYING & CURING TIME 6

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product.
Pot life after catalyzer mixing is max 2 hours
Temperature limit during application: MIN 1D"C - P4AX 40"C. Allow product to cure thoroughly before applying the next layer. Product must be perfectly dry before exposure to fog, rain or frost.

STORAGE INSTRUCTIONS 7

Packaging. Tin cans 1 kg ; 5kg ; 20 kg
Shelf life. Storage temperature min 3°C max 40°C - keep away from direct sunlight
Product Stability. SCUDOCHROMAME 502MT 5 years in original package SCUDOCATALYST 22AF 3 years in original package
Safety Instructions. Read MSDS Material safety data sheet carefully before using products.

SURFACE PREPARATION 1

Remove any contamination that could interfere with the adhesion by solvent cleaner MET (Methyl Ethyl Ketone) /alchool
In case of pitted surface carefully sand and levigate by medium /course grit paper (400-600) for maximising smoothness and flatness
Mask the parts not to be chromed by non absorbing paper or tape.

PRIMER 2

Uniformly apply cathalysed PRIMER IC100B(100%)+ TUTTOCATALYST IC80 (80%) (shake well) with a HLVP spray gun
Let dry at 60° -70° C for 70 min oror optimal results it is recomend to let the parts rest at ambient temperature for 12 hours
Allow curing in clean ambient (dust less) and never touch the coated surfaces. The surface must be perfectly plain and glossy.

CHROME 3

Shake well the TUTTOCHROMAME STD TC20 before pouring it into the HLVP spray gun (pressure 1 bar, nozzle 1-1,2/1,3 mm, to have a reduces flow of product).
Apply 3 layers of SUPACHROME with crossed strokes, until the surface is completely covered. It is reccomend to spray from bottom to top direction
Let dry at 60° -70° C for 70 min , for optimal results it is recomend attend at ambient temperature for 24 hours . The more time the solvents have to evoporate the higher will the reflectivity will be (it can reach 95%- 98% spherical refectivity).

TOP COAT 4

Apply CERAMIC TOP COAT CLEARTOP MT300(100%) + CATALYST MT439 (50%) with normal spray gun
If special coloring is required CME Pigments are to be added to CERAMIC TOP COAT CLEARTOP MT300(100%) + CATALYST MT439 (50%) according to the Mix ratio % specified for each pigment on the bottle label.
Let dry at 60° -70° C for 1,5 hour , The product can be handeld and packaged/ wrapped after 3 hours.
It is advisible to apply a second layer of CERAMIC TOP COAT CLEARTOP MT300(100%) + CATALYST MT439 (50%) after color coating for a high quality gloosy and durabale finish.

Video

SCUDOMARINE SERIES 8

FAQ

Is it difficult to use your products?

The process of applying the products may seem easy, but it's crucial to strictly adhere to the specified procedures and follow the recommended operating parameters. To ensure proper application, scan the QR code on the product label for access to the Application Data Sheet and instructional videos. Qualified customers have 24/7 online access to training and application information, and support is available by calling Mobile & WhatsApp +971 54 246 2694

I don't have any experience working with such materials, how can I start using them?

The ChromaMe® Air and Surface Nano Tech customer support service during launch looks as follows:

In pre pre-sales phase the customer will visit ChromaMe® Air and Surface Nano Tech Demonstration Labs in Italy and attend a free sampling demonstration session.
In the post sales phase the customers technical staff will be hosted at ChromaMe® Air and Surface Nano Tech Demo Labs and will attend a 3 day Special Starter Course.
The customer will receive a direct training on the job on how to use the products, learn which applications are possible and , how to avoid misuse of products
Attenders will directly perform starter applications on proprietary samples followed by our technicians that they can repeat at their own convenience once back

What is required to use ChromaMe® Air and Surface Nano Tech products?

Typical equipment used by painters for a standard paint booth setup includes a compressor, spray gun, and a clean room for storing the wet paint works. While not required, it's recommended to have an oven or infrared system to speed up the drying process of the paint.

Is any special equipment required for the application of ChromaMe® Air and Surface Nano Tech product?

ExtraChromaMe® (100% reflectivity) requires a special compact Application Machine with its unique (proprietary design) spray gun and is a complete and professional mobile paint work station. TuttoChromaMe (95% reflectivity) is applied with conventional spray guns and does not require and special equipment other than a conventional dry spray booth.

Are ChromaMe® Air and Surface Nano Tech products a new chroming process?

No, they are new solutions for conventional chrome spray painting, allowing to achieve a chrome mirror like effect on any kind of surface and material with unpreceded quality in terms of durability and reflectivitymeMe (95% reflectivity) is applied with conventional spray guns and does not require and special equipment other than a conventional dry spray booth.

Do ChromaMe® Air and Surface Nano Tech products resist to severe weather conditions and mechanical stress?

Yes ScudoChromaMe is a transparent anti fouling top coating that can be applied on all ChromaMe® Air and Surface Nano Tech Chrome paints , and also with a very significant increase of surface hardness. Results demonstrate increase in corrosion protection ( test with MEK MetilEtilCheton solvent ) abrasion and scratch resistance, UV light resistance while maintaining PlataChromaMe reflectivity close to 98%. The product is also successfully proved as a permanent antifouling for boat hulls.

Is ChromaMe® Air and Surface Nano Tech a reseller of product?

No ChromaMe® Air and Surface Nano Tech is a Italian Nano Material Engineering original manufacturer company that produces and distributes products related to Nano technology & materials all covered by patents and proprietary IP.

Can I use the ChromaMe® Air and Surface Nano Tech system in conjunction with internal spray painting business?

Yes indead you can! In fact it will enhance your current business and you will be tapping into new markets opportunities that you would never have thought possible before especially in very technological industrial applications , as well as in exterior and interior design applications in the construction industry.

Video

Do you have any questions? Contact us

FAQ